Plumbing Essentials: An Essential for Installing a Bathtub
Plumbing Essentials: An Essential for Installing a Bathtub
Blog Article
We have stumbled on this great article involving A Step-by-Step Guide to Installing a Bathtub listed below on the internet and believe it made sense to relate it with you here.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently available, the project can relocate easily; if you need to open up a wall surface to eliminate the old tub and also position the brand-new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will need a helper to move out the old tub and embeded in the new one. Make sure you have actually qualified yourself for the work and also are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This write-up will certainly aid you install a brand-new tub in your washroom if you have currently bought a brand-new bathtub as well as do not require to transform the plan of your previous supply of water pipes.
Your tools and also material checklist must comprise the following:
Planning for the Installation
To start with, the supporting frame supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets system to stop strain on the bath tub.
Fit the flexible tap connectors to the bottom of both taps making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the supply of water. After doing so, activate the taps to drain pipes any water remaining in the system. The process of getting rid of the existing faucets can be quite problematic as a result of the limited gain access to that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before going on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the bathtub up until the level reviews degree.
To set up faucets, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression join; after that do the exact same for the various other tap.
Activate the water system and also inspect all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise check the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub should wait till the tub has been made use of a minimum of once as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and also the sink. Secure the faucet in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The previous type should be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, resulting in issues with moisture and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water before sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I thought sharing that chunk was worthwhile. Don't hesitate to take the time to promote this entry if you enjoyed reading it. Bless you for your time. Come back soon.
Secure efficient service. Report this page